MSOTOR
MP
31
MP
ORDER CODE
Pos.1
Pos.2
Pos.3
Pos.4
12345678 10
Pos. 5
The hydraulic motors are mangano-phosphatized as standard.
9
Pos. 8
Pos. 7
Pos.10
Pos. 6
Pos. 9
- Mounting Flange
- (needle bearings)Option
- Port type
- Displacement code
- Design Series
-**Shaft Extensions
(see page 28)
- Shaft Seal Version
(see page 30)
- Drain Port
- Ports
- Special Features (see page 20)1
The following combinations are not allowed: - flange with “ ” shafts;Q ...B
- flange with “ ” shafts or rear ports;W ...B E
- option with “ ” shafts, Low Pressure Seal or option;N ...B U
- “ ” shafts with and shaft seals....B D U
25*
32*
50
80
100
125
160
200
250
315
400
500
40*
630
- 25,0 cm
/rev [ 1.52 in /rev]
33
- 32,0 cm /rev [ 1.95 in /rev]
33
- 40,0 cm /rev [ 2.44 in /rev]
33
- 49,5 cm /rev [ 3.02 in /rev]
33
- 79,2 cm /rev [ 4.83 in /rev]
33
- 99,0 cm /rev [ 6.04 in /rev]
33
- 158,4 cm /rev [ 9.66 in /rev]
33
- 198,0 cm /rev [12.10 in /rev]
33
- 247,5 cm /rev [15.10 in /rev]
33
- 316,8 cm /rev [19.30 in /rev]
33
- 396,0 cm /rev [24.16 in /rev]
33
- 495,0 cm /rev [30.20 in /rev]
33
- 623,6 cm /rev [38.05 in /rev]
33
- 123,8 cm /rev [ 7.55 in /rev]
33
omit
F
Q
W
- Oval mount, two holes
- Oval mount, four holes
- Square mount, four bolts
- Wheel mount
omit
- none
N
- with needle bearings
omit
- Side ports
E
- Rear ports
VSA
SA
K
VSH
SH
VCO
CO
VC
C
CB
KB
SB
OB
HB
- ø25 straight, Parallel key
A8x7x32 DIN6885
- ø25 straight, Parallel key
A8x7x32 DIN6885
with corrosion resistant bushing
- ø1" straight, Parallel key ¼"x¼"x1¼" BS46
- ø1" straight, Parallel key ¼"x¼"x1¼" BS46
with corrosion resistant bushing
- ø25,32 splined BS 2059 (SAE 6B)
- ø25,32 splined BS 2059 (SAE 6B)
with corrosion resistant bushing
- ø28,56 tapered 1:10, Parallel key B5x5x14 DIN6885
- ø24,5 splined B 25x22 DIN 5482
- ø24,5 splined B 25x22 DIN 5482
with corrosion resistant bushing
- ø32 straight, Parallel key
A10x8x45 DIN6885
- ø35 tapered 1:10, Parallel key B6x6x20 DIN6885
- splined
A 25x22 DIN 5482
- ø1¼" tapered1:8, Parallel key
"x "x1¼" BS46//
55
16 16
- ø1¼" splined 14T ANSI B92.1 - 1976
omit
- Low pressure shaft seal or Standard shaft seal
for
“... ” shaftB
- Standard shaft seal
- High pressure shaft seal (without check valves)
D
U
omit
1
- with drain port
- without drain port
omit
M
- BSPP
(ISO 228)
- Metric (ISO 262)
omit
- Factory specified
*
**
Not with Low Pressure Seal.
The permissible output torque for shafts must not be exceeded.
NOTES: